Deutsch
Français
RANGES
There are 23 products.
Active filters
FaloCS - DL149581
Colour Switchable IP44 Adjustable LED Downlight (120lm/W) with integrated Triac Dimmable LED driver. Coverable with any type of insulation material and airtight tested.
Rapid tool-free installation through loop in/loop out push-fit wiring terminals with strain relief.
Compact integrated low profile design with insulation cover allow for use in shallow voids up to 50mm.
Colour Switchable between 2700/3000/4000K.
LEDchroic lens design with 60° beam angle imitates the appearance of halogen lamps and provides controlled, uniform light distribution with minimal glare.
Rapid tool-free installation through loop in/loop out push-fit wiring terminals with strain relief.
Compact integrated low profile design with insulation cover allow for use in shallow voids up to 50mm.
Colour Switchable between 2700/3000/4000K.
LEDchroic lens design with 60° beam angle imitates the appearance of halogen lamps and provides controlled, uniform light distribution with minimal glare.
LED DRIVER - DR152840
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
Loop in/out on primary side, 3 X 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
Loop in/out on primary side, 3 X 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154585
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154592
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154615
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154622
Dimmable Phase Cut ( TRIAC) Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LEDlineCOB - ST152987
Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
LEDlineCOB - ST152994
Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
LEDlineCOB - ST153007
Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
LEDlineCOB - ST153014
Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
LEDlineCOB - ST153021
Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
LEDlineCOB - ST156589
Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
LEDlineCOB - ST159566
Tuneable White high intensity COB LED Strip with 3M self adhesive backing for continuous light without LED hotspots.
Cut points every 25mm for maximum flexibility.
Beam angle of 130° and 640 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
Cut points every 25mm for maximum flexibility.
Beam angle of 130° and 640 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.
