0

tags

    No tags have been specified yet.

Active filters

  • Categories: ASIMES CWS
  • Categories: COSMOS PRO
  • Categories: LED DRIVER
  • Categories: LED Line
  • Categories: LinearPac
  • Categories: ONExLITE

Asimes - BH156824

Colour Switchable IP65 Asymetrical Bulkhead with opal polycarbonate IK10 diffuser for even and uniform light distribution. Perfect for demanding wall and ceiling installations.
3 Colour Selections available for ultimate flexibility in every application.
IP65 rated rear entry access wiring compartment enable quick and simple through-wiring and product installation.
Suitable for ambient temperatures from -20°C to +45°C.



COSMOS PRO - HB157357

High Power IK10 impact resistant IP65 LED Highbay with superior efficiency of 180lm/W.
Tool free interchangeable Lense design. Comes with 120° lense as standard, 90° lense options available as accessory.
Integrated 0-10V dimmable LED driver pre-wired with 1500mm cable/220mm dim wire for ease of installation. 800mm safety cable included.
Zhaga base for plug and play Microwave or PIR Sensor Module with detection range up to 12m. Sensor options available as accessory.
Suitable for -40° - +50° ambient working temperature.


LED DRIVER - DR152840

Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
Loop in/out on primary side, 3 X 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).


LED DRIVER - DR154585

Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).


LED DRIVER - DR154592

Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).


LED DRIVER - DR154615

Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).


LED DRIVER - DR154622

Dimmable Phase Cut ( TRIAC) Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).


LEDlineCOB - ST152987

Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.



LEDlineCOB - ST152994

Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.



LEDlineCOB - ST153007

Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.



LEDlineCOB - ST153014

Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.



LEDlineCOB - ST153021

Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.



LEDlineCOB - ST156589

Single colour high intensity COB LED Strip with 3m self adhesive backing for continuous light without LED hotspots.
Cut points every 50mm for maximum flexibility.
Beam angle of 150° and 480 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.



LEDlineCOB - ST159566

Tuneable White high intensity COB LED Strip with 3M self adhesive backing for continuous light without LED hotspots.
Cut points every 25mm for maximum flexibility.
Beam angle of 130° and 640 LEDs per metre.
For runs over 5 metres individual lenghts should be connected in parallel.



This website uses cookies to ensure you get the best experience on our website