Deutsch
Français
RANGES
There are 27 products.
Active filters
COSMOS PRO - HB157357
High Power IK10 impact resistant IP65 LED Highbay with superior efficiency of 180lm/W.
Tool free interchangeable Lense design. Comes with 120° lense as standard, 90° lense options available as accessory.
Integrated 0-10V dimmable LED driver pre-wired with 1500mm cable/220mm dim wire for ease of installation. 800mm safety cable included.
Zhaga base for plug and play Microwave or PIR Sensor Module with detection range up to 12m. Sensor options available as accessory.
Suitable for -40° - +50° ambient working temperature.
Tool free interchangeable Lense design. Comes with 120° lense as standard, 90° lense options available as accessory.
Integrated 0-10V dimmable LED driver pre-wired with 1500mm cable/220mm dim wire for ease of installation. 800mm safety cable included.
Zhaga base for plug and play Microwave or PIR Sensor Module with detection range up to 12m. Sensor options available as accessory.
Suitable for -40° - +50° ambient working temperature.
IsoPro - DL150020
IP65 GU10 Fire Rated Downlight including GU10 lamp and Fixed Aluminium Bezel. Designed to seal ceilings completely.
Rapid installation through loop in/loop out push-fit wiring terminals with strain relief.
Fully insulation coverable (blown or unwound) without the need of additional accessory or insulation cut-out. Vapour-barrier compatible.
ISOPRO Kit includes the GU10 ICE lamp with superior thermal management which has been specifically designed and tested in closed fire rated and insulation covered downlights Tested in 30, 60 and 90 minutes fire-rated ceilings according to EN1365-2.
Airtight and Acoustics rated.
Rapid installation through loop in/loop out push-fit wiring terminals with strain relief.
Fully insulation coverable (blown or unwound) without the need of additional accessory or insulation cut-out. Vapour-barrier compatible.
ISOPRO Kit includes the GU10 ICE lamp with superior thermal management which has been specifically designed and tested in closed fire rated and insulation covered downlights Tested in 30, 60 and 90 minutes fire-rated ceilings according to EN1365-2.
Airtight and Acoustics rated.
IsoPro - DL150068
IP65 GU10 Fire Rated Downlight including GU10 lamp and Fixed Aluminium Bezel. Designed to seal ceilings completely.
Rapid installation through loop in/loop out push-fit wiring terminals with strain relief.
Fully insulation coverable (blown or unwound) without the need of additional accessory or insulation cut-out. Vapour-barrier compatible.
ISOPRO Kit includes the GU10 ICE lamp with superior thermal management which has been specifically designed and tested in closed fire rated and insulation covered downlights Tested in 30, 60 and 90 minutes fire-rated ceilings according to EN1365-2.
Airtight and Acoustics rated.
Rapid installation through loop in/loop out push-fit wiring terminals with strain relief.
Fully insulation coverable (blown or unwound) without the need of additional accessory or insulation cut-out. Vapour-barrier compatible.
ISOPRO Kit includes the GU10 ICE lamp with superior thermal management which has been specifically designed and tested in closed fire rated and insulation covered downlights Tested in 30, 60 and 90 minutes fire-rated ceilings according to EN1365-2.
Airtight and Acoustics rated.
LED DRIVER - DR152840
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
Loop in/out on primary side, 3 X 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
Loop in/out on primary side, 3 X 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154585
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154592
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154615
Non-dimmable Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LED DRIVER - DR154622
Dimmable Phase Cut ( TRIAC) Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LEDline - DR154639
Dimmable Phase Cut ( TRIAC) Constant Voltage (CV) LED driver.
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
SELV type with Short circuit, Overload and Over voltage protection.
2 x 24 VDC outputs on screw terminal block.
IP20 for indoor use.
Independent cable clamps ( inlet / outlet ).
LEDline - ST153038
High intensity SMD LED Strip with 3m self adhesive tape.
Cut points every 50mm for maximum flexibility.
Beam angle of 120° and 120 LEDs per metre.
For runs over 10 metres individual lengths should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 120° and 120 LEDs per metre.
For runs over 10 metres individual lengths should be connected in parallel.
LEDline - ST153045
High intensity SMD LED Strip with 3m self adhesive tape.
Cut points every 50mm for maximum flexibility.
Beam angle of 120° and 120 LEDs per metre.
For runs over 10 metres individual lengths should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 120° and 120 LEDs per metre.
For runs over 10 metres individual lengths should be connected in parallel.
LEDline - ST153052
High intensity SMD LED Strip with 3m self adhesive tape.
Cut points every 50mm for maximum flexibility.
Beam angle of 120° and 120 LEDs per metre.
For runs over 10 metres individual lengths should be connected in parallel.
Cut points every 50mm for maximum flexibility.
Beam angle of 120° and 120 LEDs per metre.
For runs over 10 metres individual lengths should be connected in parallel.
