Eco LED Backlit Panel with optical pattern PMMA lenses engineered for even and uniform light distribution offer best value for money. Opal diffuser provides glare control with achievable UGR19. Suitable for installations in 15 and 24mm t-bar ceilings as well as ceiling suspension, surface mount or recess mount in plasterboard. Flicker-free non-dimmable LED driver pre-wired for simplified and fast installation.
Eco LED Backlit Panel with optical pattern PMMA lenses engineered for even and uniform light distribution offer best value for money. Opal diffuser provides glare control with achievable UGR19. Suitable for installations in 15 and 24mm t-bar ceilings as well as ceiling suspension, surface mount or recess mount in plasterboard. Flicker-free non-dimmable LED driver pre-wired for simplified and fast installation.
The DR159481 driver is a dimmable 1-10V driver with adjustable constant current. It is supplied complete with a cable for connection to the luminaire. Dimming range from 5 to 100%. No flicker and smooth dimming in all light conditions. Output current adjustment ( 10 levels ) by means of micro-switches. Support CBS , central emergency application. Independent cable clamps ( inlet / outlet ).
The DR159429 driver is a dimmable DALI-2 and PushDIM driver with adjustable constant current. It is supplied complete with a cable for connection to the luminaire. Dimming range from 1 to 100%. No flicker and smooth dimming in all light conditions. Output current adjustment ( 10 levels ) by means of micro-switches. Support CBS , central emergency application. Independent cable clamps ( inlet / outlet ).
Colour Switchable IP44 Adjustable LED Downlight (120lm/W) with integrated Triac Dimmable LED driver. Coverable with any type of insulation material and airtight tested. Rapid tool-free installation through loop in/loop out push-fit wiring terminals with strain relief. Compact integrated low profile design with insulation cover allow for use in shallow voids up to 50mm. Colour Switchable between 2700/3000/4000K. LEDchroic lens design with 60° beam angle imitates the appearance of halogen lamps and provides controlled, uniform light distribution with minimal glare.
Non-dimmable Constant Voltage (CV) LED driver. SELV type with Short circuit, Overload and Over voltage protection. Loop in/out on primary side, 3 X 24 VDC outputs on screw terminal block. IP20 for indoor use. Independent cable clamps ( inlet / outlet ).
Non-dimmable Constant Voltage (CV) LED driver. SELV type with Short circuit, Overload and Over voltage protection. 2 x 24 VDC outputs on screw terminal block. IP20 for indoor use. Independent cable clamps ( inlet / outlet ).
Non-dimmable Constant Voltage (CV) LED driver. SELV type with Short circuit, Overload and Over voltage protection. 2 x 24 VDC outputs on screw terminal block. IP20 for indoor use. Independent cable clamps ( inlet / outlet ).
Non-dimmable Constant Voltage (CV) LED driver. SELV type with Short circuit, Overload and Over voltage protection. 2 x 24 VDC outputs on screw terminal block. IP20 for indoor use. Independent cable clamps ( inlet / outlet ).
Dimmable Phase Cut ( TRIAC) Constant Voltage (CV) LED driver. SELV type with Short circuit, Overload and Over voltage protection. 2 x 24 VDC outputs on screw terminal block. IP20 for indoor use. Independent cable clamps ( inlet / outlet ).
Dimmable Phase Cut ( TRIAC) Constant Voltage (CV) LED driver. SELV type with Short circuit, Overload and Over voltage protection. 2 x 24 VDC outputs on screw terminal block. IP20 for indoor use. Independent cable clamps ( inlet / outlet ).
High intensity SMD LED Strip with 3m self adhesive tape. Cut points every 50mm for maximum flexibility. Beam angle of 120° and 120 LEDs per metre. For runs over 10 metres individual lengths should be connected in parallel.
High intensity SMD LED Strip with 3m self adhesive tape. Cut points every 50mm for maximum flexibility. Beam angle of 120° and 120 LEDs per metre. For runs over 10 metres individual lengths should be connected in parallel.
High intensity SMD LED Strip with 3m self adhesive tape. Cut points every 50mm for maximum flexibility. Beam angle of 120° and 120 LEDs per metre. For runs over 10 metres individual lengths should be connected in parallel.
Deutsch
Français
